Intensive quantity, heat capacity per amount of substance
The molar heat capacity of a chemical substance is the amount of energy that must be added, in the form of heat, to one mole of the substance in order to cause an increase of one unit in its temperature. Alternatively, it is the heat capacity of a sample of the substance divided by the amount of substance of the sample; or also the specific heat capacity of the substance times its molar mass. The SI unit of molar heat capacity is joule per kelvin per mole, J⋅K−1⋅mol−1.
Like the specific heat, the measured molar heat capacity of a substance, especially a gas, may be significantly higher when the sample is allowed to expand as it is heated (at constant pressure, or isobaric) than when it is heated in a closed vessel that prevents expansion (at constant volume, or isochoric). The ratio between the two, however, is the same heat capacity ratio obtained from the corresponding specific heat capacities.
This property is most relevant in chemistry, when amounts of substances are often specified in moles rather than by mass or volume. The molar heat capacity generally increases with the molar mass, often varies with temperature and pressure, and is different for each state of matter. For example, at atmospheric pressure, the (isobaric) molar heat capacity of water just above the melting point is about 76 J⋅K−1⋅mol−1, but that of ice just below that point is about 37.84 J⋅K−1⋅mol−1. While the substance is undergoing a phase transition, such as melting or boiling, its molar heat capacity is technically infinite, because the heat goes into changing its state rather than raising its temperature. The concept is not appropriate for substances whose precise composition is not known, or whose molar mass is not well defined, such as polymers and oligomers of indeterminate molecular size.
A closely related property of a substance is the heat capacity per mole of atoms, or atom-molar heat capacity, in which the heat capacity of the sample is divided by the number of moles of atoms instead of moles of molecules. So, for example, the atom-molar heat capacity of water is 1/3 of its molar heat capacity, namely 25.3 J⋅K−1⋅mol−1.
In informal chemistry contexts, the molar heat capacity may be called just "heat capacity" or "specific heat". However, international standards now recommend that "specific heat capacity" always refer to capacity per unit of mass, to avoid possible confusion.[1] Therefore, the word "molar", not "specific", should always be used for this quantity.
^International Bureau of Weights and Measures (2006), The International System of Units (SI)(PDF) (8th ed.), ISBN 92-822-2213-6, archived (PDF) from the original on 2021-06-04, retrieved 2021-12-16
and 29 Related for: Molar heat capacity information
The molarheatcapacity of a chemical substance is the amount of energy that must be added, in the form of heat, to one mole of the substance in order...
dividing the heatcapacity of an object by its mass. Dividing the heatcapacity by the amount of substance in moles yields its molarheatcapacity. The volumetric...
amount of substance is measured as a number of moles, one gets the molarheatcapacity instead, whose SI unit is joule per kelvin per mole, J⋅mol−1⋅K−1...
and (when applicable) the molarheatcapacity. Generally, the most notable constant parameter is the volumetric heatcapacity (at least for solids) which...
chemistry), one gets the molarheatcapacity (whose SI unit is joule per kelvin per mole, J⋅K−1⋅mol−1). The volumetric heatcapacity is defined as s ( T )...
C_{p_{k}}} is the molarheatcapacity at a constant pressure of the substance in the reversible process k. The molarheatcapacity is not constant during...
Tc_{P,m}\end{aligned}}} where cP is molarheatcapacity at a constant pressure. To find the molar specific heatcapacity of the gas involved, the following...
m ∘ {\displaystyle C_{P,\mathrm {m} }^{\circ }} is the standard molarheatcapacity of a substance at constant pressure. Δ r H m ∘ {\displaystyle \mathrm...
constant-volume molarheatcapacity Cv is constant and there is no phase change. At low temperatures near absolute zero, heatcapacities of solids quickly...
capacity, one gets the molarheatcapacity, which is about 75.385 J/(K⋅mol) for water and about 25.10 J/(K⋅mol) for iron. The molar mass of a substance is...
constant. Since R ≈ 2 cal/(mol·K), equipartition predicts that the molarheatcapacity of an ideal gas is roughly 3 cal/(mol·K). This prediction is confirmed...
monatomic gases: the molarheatcapacity at constant pressure (Cp) is 5/2 R = 20.8 J⋅K−1⋅mol−1 (4.97 cal⋅K−1⋅mol−1). the molarheatcapacity at constant volume...
dioxide is therefore more effective than nitrogen due to its higher molarheatcapacity. The concept has important practical use in fire safety engineering...
In thermodynamics, the heatcapacity at constant volume, C V {\displaystyle C_{V}} , and the heatcapacity at constant pressure, C P {\displaystyle C_{P}}...
molar gas constant (also known as the gas constant, universal gas constant, or ideal gas constant) is denoted by the symbol R or R. It is the molar equivalent...
partial molar property become equal. Some apparent molar properties that are commonly used are apparent molar enthalpy, apparent molarheatcapacity, and...
avalanche is created when heat produces free electrons and holes, which in turn pass more current, which produces more heat). In addition, the insulating...
power. Heat produced by the deceleration of these alpha particles makes it warm to the touch. 238 Pu due to its much shorter half life heats up to much...
plastics. In the absence of such stabilizers, PVC would rapidly degrade under heat, light, and atmospheric oxygen, resulting in discolored, brittle products...
separate nitroaereus from air and pass it into the blood and that animal heat and muscle movement result from the reaction of nitroaereus with certain...
layer in daguerreotypy. By 1864, a 25% solution of liquid bromine in .75 molar aqueous potassium bromide was widely used to treat gangrene during the American...
absence of π-acceptor ligands. Silver does not react with air, even at red heat, and thus was considered by alchemists as a noble metal, along with gold...
are brittle, however, and may crack under a sharp blow. The hardness and heat resistance of tungsten can contribute to useful alloys. A good example is...
pure copper has a pinkish-orange color. Copper is used as a conductor of heat and electricity, as a building material, and as a constituent of various...
Global Information