A threaded rod, also known as a stud, is a relatively long rod that is threaded on both ends; the thread may extend along the complete length of the rod.[1] They are designed to be used in tension.[2] Threaded rod in bar stock form is often called all-thread (ATR); other names include fully-threaded rod, redi-rod, continuously-threaded rod, and TFL rod.[3]
Galvanized steel,[3] mild steel, stainless steel, nylon, brass, copper, aluminum, and titanium are all commonly used to make threaded rods.[4]
^Soled, Julius (1957), Fasteners handbook, Reinhold Publishing, p. 90.
^Speck, James A. (1997), Mechanical fastening, joining, and assembly, CRC Press, p. 54, ISBN 978-0-8247-9835-2.
^ ab"All Thread Rods - Portland Bolt". 31 July 2014.
^"A guide to threaded rods". www.essentracomponents.com.
A threadedrod, also known as a stud, is a relatively long rod that is threaded on both ends; the thread may extend along the complete length of the rod...
bulb. At the top of the harp is a threadedrod. The shade's internal frame (known as a spider) mounts on this rod and is secured in place by a lamp finial...
driven apart (or together) at a constant rate, usually by turning a threadedrod or bolt. This is called a tangent drive. This type of mount is good for...
to create screw threadsThreadedrod – Rod with ridges wrapped around it Threading (manufacturing) – Process of creating a screw thread Wall plug – Insert...
A sucker rod is a steel rod, typically between 25 and 30 feet (7 to 9 meters) in length, and threaded at both ends, used in the oil industry to join together...
extraction. Two threaded tongs held a centre threaded shaft, which could be inserted into the wound: the shape was not unlike a tapered threadedrod inside a...
joint Dowel bar retrofit Fastener Kinematic coupling Rebar Spring pin Threadedrod Treenail Ivin Sickels, Exercises in Wood-Working, American Book Company...
with headed studs welded on (see also threadedrod). Threaded sleeves: consist of a tube with an internal thread which is anchored back into the concrete...
the rod. The ends may be threaded and passed through drilled holes or shackles and retained by nuts screwed on the ends. If the ends are threaded right-...
Punched channel has round holes, large enough for an M16 or 5/8 inch threaded steel rod or bolts, punched in the top of the channel at regular 48 mm (1 7/8 inch)...
be produced by the printer itself). These parts include threadedrods, leadscrews, smooth rods and bearings, screws, nuts, stepper motors, control circuit...
of a shoe worn for playing sports Shirt stud, a decorative fastener Threadedrod, a kind of bolt Wall stud, a vertical member in construction Studs, small...
loose nut is placed on this threadedrod with a diameter of only around 1.5 mm and screwed on by hand. A threadedrod is enough. By tightening the nut...
nut, also known as extension nut, is a threaded fastener for joining two male threads, most commonly a threadedrod, but also pipes. The outside of the fastener...
long tension rod with a threaded end extends through the hoop holding the top drum head and then down outside the drum shell to a threaded hole in the...
helically grooved cylinder mounted on a correspondingly threadedrod supported by plain and threaded bearings. While the cylinder was rotated and slowly progressed...
more specialized types of threaded fasteners include captive threaded fasteners, stud, threaded inserts, and threadedrods. Other types of fastener include:...
bedrock by ninety-six 2+1⁄2-inch-diameter (64 mm) high strength steel threadedrod rock anchors grouted 46 feet (14 m) deep into the rock. The deck of the...
with a threaded shaft attached. The threaded portion may be either male or female. The heim joint's advantage is that the ball insert permits the rod or bolt...
century use a thread pitch around 2 mm (12.7 TPI), while many modern rifle use thread pitches around 1.5 mm (16.93 TPI). Fine threaded systems intended...
place with nothing more complex than a couple of nuts, washers and a threadedrod. A more serious problem with this type of propeller is a "frozen-on"...
consists of a male threaded fastener (e. g., a bolt) that captures and joins other parts, secured with a matching female screw thread. There are two main...
possible. The specimen to be examined was mounted on a point on a finely threadedrod. Compound light microscopes have a short focal length objective lens...
racing mountain bike cranksets use a Hirth joint with a center hex-head threadedrod to secure the crank halves together. The crank design and technology...