Global InformationMars Excursion Module information
The Mars Excursion Module (MEM) was a spacecraft proposed by NASA in the 1960s for use in a human mission to Mars, and this can refer to any number of studies by corporations and spaceflight centers for Mars landers. However, primarily a MEM referred to a combination of a Manned Mars lander, short-stay surface habitat, and Mars ascent stage. Variations on a MEM included spacecraft designs like an uncrewed Mars surface cargo delivery, and there was a MEM lander that combined a communications center, living habitat, and laboratory.[1]
A MEM formed part of Mars orbit rendezvous (MOR) and flyby-rendezvous mission profiles studied at NASA's Manned Spacecraft Center in the 1960s.[2] A Mars Excursion Module would have been a combination of a Mars lander, short-stay surface habitat, and ascent vehicle; the ascent stage performed the rendezvous. One design for a MEM would have been used for a 40-day stay on the Martian surface in the flyby-rendezvous mission profile or for a 10- to 40-day stay in the MOR profiles.[2] There was also a descent-only uncrewed MEM for delivering cargo, like a rover to the surface of Mars.[3] Another MEM cargo lander variant would deliver a nuclear reactor to support the surface operations, and there was another with a communications, living quarters and lab in one landing-only MEM unit.[1]
In the early 1960s, NASA contracted Philco Corporation to design a Mars Excursion Module for a Mars mission for the early 1970s.[4] The basic requirements were for a crew of two, one US ton of science hardware, and to support 40 days of surface operation on Mars.[4] Another MEM from this period was the Ames contracted TRW MEM, a design which weighed 11.4 metric tons but was designed for Mars atmosphere which had 10% of Earth's.[5] The TRW MEM would support 10 days on the surface.[5]
In 1964, Philco Aeronutronic proposed a lifting body MEM, approximately 30 feet (9.1 m) long and 33 feet (10 m) wide at the tail, which would carry three astronauts. The hull would have consisted of columbium and nickel alloy. The MEM's descent stage would have served as the launch pad for liftoff of the ascent stage, as with the Apollo Lunar Module.[2]
A Mars Excursion Module was discussed as a possibility in the Space Task Group Report of 1969, with a development decision required in FY 1974 for a 1981 Mars mission or in FY 1978 for a 1986 mission.[6]
The watershed moment for mission planning was July 1965, when Mariner IV returned more accurate atmospheric data about Mars.[3] This ruled out many of the lifting body and glider designs that were being considered based on estimates of a thicker Mars atmosphere than revealed by Mariner IV.[3]
Gordon Woodcock at the NASA Marshal Space Flight Center worked on the basis of a thinner Mars atmosphere (0.5 percent of Earth's), and developed design for a MEM, and also a pure-lander variant that would deliver a pressurized crewed Mars rover called Molab.[3]
- ^ a b Woodcock, G. R. (7 June 1966). "An Initial Concept of a Manned Mars Excursion Vehicle for a Tenuous Mars Atmosphere" (PDF). NASA. Retrieved 22 September 2018.
- ^ a b c Portree, David S. F. (February 2001). "Chapter 3: Empire and After". Humans to Mars: Fifty Years of Mission Planning, 1950–2000 (PDF). NASA Monographs in Aerospace History Series. National Aeronautics and Space Administration. pp. 15–18. Retrieved 18 July 2014.
- ^ a b c d "Origin of the Apollo-shaped Manned Mars Lander (1966)". Wired. 25 October 2012. Retrieved 4 March 2018.
- ^ a b Thompson, Robert; Cliatt, Larry; Gruber, Chris; et al. (23 June 2007). "Design of an Entry System for Cargo Delivery to Mars" (PDF). NASA. Archived from the original (PDF) on 22 December 2016. Retrieved 22 September 2018.
- ^ a b "TRW Mars". Astronautix.com. Archived from the original on December 28, 2016. Retrieved 22 September 2018.
- ^ "Report of the Space Task Group, 1969". NASA. September 1969. Retrieved 10 July 2014.