External mixture preparation system for internal combustion engines
Manifold injection is a mixture formation system for internal combustion engines with external mixture formation. It is commonly used in engines with spark ignition that use petrol as fuel, such as the Otto engine, and the Wankel engine. In a manifold-injected engine, the fuel is injected into the intake manifold, where it begins forming a combustible air-fuel mixture with the air. As soon as the intake valve opens, the piston starts sucking in the still forming mixture. Usually, this mixture is relatively homogeneous, and, at least in production engines for passenger cars, approximately stoichiometric; this means that there is an even distribution of fuel and air across the combustion chamber, and enough, but not more air present than what is required for the fuel's complete combustion. The injection timing and measuring of the fuel amount can be controlled either mechanically (by a fuel distributor), or electronically (by an engine control unit). Since the 1970s and 1980s, manifold injection has been replacing carburettors in passenger cars. However, since the late 1990s, car manufacturers have started using petrol direct injection, which caused a decline in manifold injection installation in newly produced cars.
There are two different types of manifold injection:
the multi-point injection(MPI) system, also known as port injection, or dry manifold system
and the single-point injection(SPI) system, also known as throttle-body injection (TBI), central fuel injection (CFI), electronic gasoline injection (EGI), and wet manifold system
In this article, the terms multi-point injection (MPI), and single-point injection (SPI) are used. In an MPI system, there is one fuel injector per cylinder, installed very close to the intake valve(s). In an SPI system, there is only a single fuel injector, usually installed right behind the throttle valve. Modern manifold injection systems are usually MPI systems; SPI systems are now considered obsolete.
and 25 Related for: Manifold injection information
Manifoldinjection is a mixture formation system for internal combustion engines with external mixture formation. It is commonly used in engines with spark...
A fuel injection system that uses external mixture formation is called a manifoldinjection system. There exist two types of manifoldinjection systems:...
chamber. This is distinct from manifoldinjection systems, which inject fuel into the intake manifold (inlet manifold). The use of GDI can help increase...
Jetronic is a trade name of a manifoldinjection technology for automotive petrol engines, developed and marketed by Robert Bosch GmbH from the 1960s onwards...
lower pressure manifoldinjection systems) or high-pressure mechanical pumps mounted on the engine (for high-pressure direct injection systems). Some...
primary function of the intake manifold is to evenly distribute the combustion mixture (or just air in a direct injection engine) to each intake port in...
Technology Motronic for manifoldinjection Bosch Automotive Technology Electronic throttle control (ETC/EGAS) for manifoldinjection Hutton, Ray (1 September...
air is free to fill the intake manifold, increasing the pressure (filling the vacuum). A carburetor or fuel injection system adds fuel to the airflow...
Secondary air injection (commonly known as air injection) is a vehicle emissions control strategy introduced in 1966, wherein fresh air is injected into...
engine includes fully sequential electronic multi-point fuel injection with intake manifold-sited fuel injectors, mapped direct ignition system with solid-state...
intake manifold. Some variants use multi-port fuel injection, some have D4 direct injection, and others have a combination of direct injection and multi-port...
8–2.0 L Manifoldinjection N43 Inline-four N.A. 2007–2011 1.6–2.0 L Direct injection N13 Inline-four turbo 2011–2015 1.6 L Direct injection N20 Inline-four...
crankshaft and gearbox are combined in one housing - and has intake manifoldinjection; The alternator is on the right of the crankshaft, the primary drive...
stroke along with different pistons, a different air intake manifold and exhaust manifolds as well as custom engine programming. It has a bore of 93 mm...
motorcycle with multi-point injection; the VFR800FI. The PGM-FI system relies on a piezoelectric sensor to measure intake manifold air pressure, then combines...
The manifold absolute pressure sensor (MAP sensor) is one of the sensors used in an internal combustion engine's electronic control system. Engines that...
The Bendix Electrojector is an electronically controlled manifoldinjection (EFI) system developed and made by Bendix Corporation. In 1957, American Motors...
turbocharged fuel system multi-point electronic indirect fuel injection with three intake manifold-sited fuel injectors DIN-rated motive power & torque outputs...
carburetor to fuel injection without significantly altering the intake manifold design. More complex later designs use intake manifolds, and even cylinder...
automotive engineering, an exhaust manifold collects the exhaust gases from multiple cylinders into one pipe. The word manifold comes from the Old English word...
gasoline-fueled, spark plug ignition engine of any kind produced with manifoldinjection. It was typically rated at 37 kW (50 hp). First produced in 1906 it...
intake manifolds Ignition system: Electronic ignition system with three spark plugs per rotor Fuel system: Nippon Denso electronic manifoldinjection Lubrication...
Global Information