Chilled beam information

A chilled beam is a type of radiation/convection HVAC system designed to heat and cool large buildings through the use of water.^[1] This method removes most of the zone sensible local heat gains and allows the flow rate of pre-conditioned air from the air handling unit to be reduced, lowering by 60% to 80% the ducted design airflow rate and the equipment capacity requirements.^[2] There are two types of chilled beams, a Passive Chilled Beam (PCB) and an Active Chilled Beam (ACB). They both consist of pipes of water (fin-and-tube) that pass through a heat exchanger contained in a case suspended from, or recessed in, the ceiling.^[3]^[4] As the beam cools the air around it, the air becomes denser and falls to the floor. It is replaced by warmer air moving up from below, causing a constant passive air movement called convection, to cool the room.^[5]^[6] The active beam consists of air duct connections, induction nozzles, hydronic heat transfer coils, supply outlets and induced air inlets. It contains an integral air supply that passes through nozzles, and induces air from the room to the cooling coil. For this reason, it has a better cooling capacity than the passive beam. Instead, the passive beam provides space cooling without the use of a fan and it is mainly done by convection.^[2] Passive beams can be either exposed or recessed. The passive approach can provide higher thermal comfort levels,^[7] while the active approach (also called an "induction diffuser")^[8] uses the momentum of ventilation air that enters at relatively high velocity to induce the circulation of room air through the unit (thus increasing its heating and cooling capacity).^[5] A chilled beam is similar in appearance to a VRF unit.

The chilled beam is distinguishable from the chilled ceiling.^[9]^[8] The chilled ceiling uses water flow through pipes like a chilled beam does; however, the pipes in a chilled ceiling lie behind metal ceiling plates, and the heated/cooled plates are the cause of the radiation/convection and not the pipe unit itself.^[9] Chilled beams are about 85 percent more effective at convection than chilled ceilings.^[9] The chilled ceiling must cover a relatively large ceiling area both because it is less efficient, and because it provides heating mainly by radiant means. Radiant heating capacity is proportional to surface area.^[10]

^ Oughton, Hodkinson, and Faber, 2008, p. 222-224.
^ ^a ^b American Society of Heating, Refrigerating and Air-Conditioning Engineers (2020). 2020 ASHRAE handbook : heating, ventilating, and air-conditioning systems and equipment. Refrigerating and Air-Conditioning Engineers American Society of Heating. American Society of Heating Refrigerating and Air-Conditioning Engineers Incorporated (ASHRAE). p. 20.12. ISBN 978-1-5231-3507-3.
^ Price, 2011, Engineer's HVAC Handbook, p. 1067, ISBN 978-0-9868802-0-9
^ 2012 ASHRAE Handbook HVAC Systems and Equipment, ASHRAE, 2012, p. 20.9, ISBN 978-1-936504-25-1
^ ^a ^b Hamilton and Watkins, 2009, p. 158.
^ Levermore, 2000, p. 407.
^ "Module 65: Applying chilled beams to reduce building total carbon footprint". CIBSE Journal. Retrieved 2020-02-09.
^ ^a ^b Roth, Kurt; Dieckmann, John; Zogg, Robert; and Brodrick, James. "Chilled Beam Cooling." ASHRAE Journal. September 2007.
^ ^a ^b ^c Beggs, 2009, p. 271.
^ Chilled beam vs. chilled ceiling, Severn Group|accessed June 2019

[1] Oughton, Hodkinson, and Faber, 2008, p. 222-224.

[:0-2] American Society of Heating, Refrigerating and Air-Conditioning Engineers (2020). 2020 ASHRAE handbook : heating, ventilating, and air-conditioning systems and equipment. Refrigerating and Air-Conditioning Engineers American Society of Heating. American Society of Heating Refrigerating and Air-Conditioning Engineers Incorporated (ASHRAE). p. 20.12. ISBN 978-1-5231-3507-3.

[Price-3] Price, 2011, Engineer's HVAC Handbook, p. 1067, ISBN 978-0-9868802-0-9

[2012_ASHRAE_Handbook-4] 2012 ASHRAE Handbook HVAC Systems and Equipment, ASHRAE, 2012, p. 20.9, ISBN 978-1-936504-25-1

[HamWat158-5] Hamilton and Watkins, 2009, p. 158.

[6] Levermore, 2000, p. 407.

[7] "Module 65: Applying chilled beams to reduce building total carbon footprint". CIBSE Journal. Retrieved 2020-02-09.

[Roth-8] Roth, Kurt; Dieckmann, John; Zogg, Robert; and Brodrick, James. "Chilled Beam Cooling." ASHRAE Journal. September 2007.

[Beggs-9] Beggs, 2009, p. 271.

[10] Chilled beam vs. chilled ceiling, Severn Group|accessed June 2019

Chilled beam information

and 27 Related for: Chilled beam information

Chilled beam

Radiant heating and cooling

Chilled water

Fan coil unit

Latent heat

Mechanical engineering

Room temperature

Freon

Plenum space

Vapour pressure of water

Thermal insulation

Humidity

Variable refrigerant flow

Thermal expansion valve

Sensible heat

BACnet

Packaged terminal air conditioner

Thermosiphon

Mechanical room

Einstein refrigerator

Variable air volume

Thermodynamics

Outgassing

Dehumidifier

Heating system

Stack effect

Oil heater