A direct shear test is a laboratory or field test used by geotechnical engineers to measure the shear strength properties of soil[1][2] or rock[2] material, or of discontinuities in soil or rock masses.[2][3]
The U.S. and U.K. standards defining how the test should be performed are ASTM D 3080, AASHTO T236 and BS 1377-7:1990, respectively. For rock the test is generally restricted to rock with (very) low shear strength. The test is, however, standard practice to establish the shear strength properties of discontinuities in rock.
The test is performed on three or four specimens from a relatively undisturbed soil sample. A specimen is placed in a shear box which has two stacked rings to hold the sample; the contact between the two rings is at approximately the mid-height of the sample. A confining stress is applied vertically to the specimen, and the upper ring is pulled laterally until the sample fails, or through a specified strain. The load applied and the strain induced is recorded at frequent intervals to determine a stress–strain curve for each confining stress.
Several specimens are tested at varying confining stresses to determine the shear strength parameters, the soil cohesion (c) and the angle of internal friction, commonly known as friction angle (). The results of the tests on each specimen are plotted on a graph with the peak (or residual) stress on the y-axis and the confining stress on the x-axis. The y-intercept of the curve which fits the test results is the cohesion, and the slope of the line or curve is the friction angle.
Direct shear tests can be performed under several conditions. The sample is normally saturated before the test is run, but can be run at the in-situ moisture content. The rate of strain can be varied to create a test of undrained or drained conditions, depending on whether the strain is applied slowly enough for water in the sample to prevent pore-water pressure buildup. A direct shear test machine is required to perform the test. The test using the direct shear machine determines the consolidated drained shear strength of a soil material in direct shear.[4]
The advantages of the direct shear test [5] over other shear tests are the simplicity of setup and equipment used, and the ability to test under differing saturation, drainage, and consolidation conditions. These advantages have to be weighed against the difficulty of measuring pore-water pressure when testing in undrained conditions, and possible spuriously high results from forcing the failure plane to occur in a specific location.
The test equipment and procedures are slightly different for test on discontinuities.[6]
^Cite error: The named reference Bardet1997 was invoked but never defined (see the help page).
^ abcCite error: The named reference Price2009 was invoked but never defined (see the help page).
^Cite error: The named reference ISRMbluebook2007 was invoked but never defined (see the help page).
^"Direct shear test machine". www.cooper.co.uk. Cooper Research Technology. Archived from the original on 27 August 2014. Retrieved 8 September 2014.
^"Direct Shear Test; To Determine Shear Strength of Soil. - CivilPie". CivilPie. 2018-05-31. Retrieved 2018-06-06.
^Cite error: The named reference HencherRichards1989 was invoked but never defined (see the help page).
A directsheartest is a laboratory or field test used by geotechnical engineers to measure the shear strength properties of soil or rock material, or...
A triaxial sheartest is a common method to measure the mechanical properties of many deformable solids, especially soil (e.g., sand, clay) and rock, and...
cheap method to estimate the resilient modulus. Directsheartest ASTM D3080. The directsheartest determines the consolidated, drained strength properties...
density Triaxial sheartestDirectsheartest Relative density Oedometer test for consolidation California bearing ratio (CBR) Permeability tests (constant-head...
Thixotropy is a time-dependent shear thinning property. Certain gels or fluids that are thick or viscous under static conditions will flow (become thinner...
This is essentially due to a decrease in the shear strength of the slope material, an increase in the shear stress borne by the material, or a combination...
amplitude shear strain. This is a soil test-based definition, usually performed via cyclic triaxial, cyclic direct simple shear, or cyclic torsional shear type...
A sieve analysis (or gradation test) is a practice or procedure used in geology, civil engineering, and chemical engineering to assess the particle size...
stability, and a narrow stem with graduations for measuring. The liquid to test is poured into a tall container, often a graduated cylinder, and the hydrometer...
stretched clay lumps (a phenomenon called boudinage) and zones of concentrated shear. Debris flow deposits take the form of long, narrow tracks of very poorly...
are not always comparable. One method is the triaxial sheartest, another is the directsheartest. The measured angle of repose may vary with the method...
planted with vegetation to create a green wall. Civil engineering Directsheartest Earthquake engineering Flying arch Foundation (engineering) Geotechnical...
Laboratory tests using soil samples subjected to hydraulic experiments Field tests (on site, in situ) that are differentiated into: small-scale field tests, using...
easily identified using X-ray diffraction rather than chemical or physical tests. Varve (or varved clay) is clay with visible annual layers that are formed...
sample, and D {\displaystyle D} is mass of dried sample. In addition to the direct and laboratory methods above, the following options are available. There...
monitoring wells or piezometers. Samples collected from boreholes are often tested in a laboratory to determine their physical properties, or to assess levels...
In most cases, the rupture speed approaches, but does not exceed, the shear wave (S-wave) velocity of the surrounding rock. There are a few exceptions...
criticized for various reasons. Other erosion testing methods may produce values for erodibility and critical shear stress inconsistent with this method. Additionally...
tests measure the "accessible void", the total amount of void space accessible from the surface (cf. closed-cell foam). There are many ways to test porosity...
Global Information