For custom battery connectors, see battery terminals.
This article has multiple issues. Please help improve it or discuss these issues on the talk page. (Learn how and when to remove these template messages)
This article relies largely or entirely on a single source. Relevant discussion may be found on the talk page. Please help improve this article by introducing citations to additional sources. Find sources: "Battery holder" – news · newspapers · books · scholar · JSTOR(April 2011)
This article includes a list of general references, but it lacks sufficient corresponding inline citations. Please help to improve this article by introducing more precise citations.(June 2010) (Learn how and when to remove this message)
(Learn how and when to remove this message)
An alkaline battery in holder with pressure contacts1987 lithium coin cell battery holder
A battery holder is one or more compartments or chambers for holding a battery. For dry cells, the holder must also make electrical contact with the battery terminals. For wet cells, cables are often connected to the battery terminals, as is found in automobiles or emergency lighting equipment.
A battery holder is either a plastic case with the shape of the housing moulded as a compartment or compartments that accepts a battery or batteries, or a separate plastic holder that is mounted with screws, eyelets, glue, double-sided tape, or other means. Battery holders may have a lid to retain and protect the batteries or may be sealed to prevent damage to circuitry and components from battery leakage. Coiled spring wire or flat tabs that press against the battery terminals are the two most common methods of making the electrical connection inside a holder. External connections on battery holders are usually made by contacts with pins, surface mount feet, solder lugs, or wire leads.
Where the battery is expected to last over the life of the product, no holder is necessary, and a tab welded to the battery terminals can be directly soldered to a printed circuit board.
A batteryholder is one or more compartments or chambers for holding a battery. For dry cells, the holder must also make electrical contact with the battery...
portal BatteryholderBattery recycling Battery (vacuum tube) Comparison of commercial battery types List of battery types Search for the Super Battery, a...
The C battery (C size battery or R14 battery) is a standard size of dry cell battery typically used in medium-drain applications such as toys, flashlights...
(negative). These mate with metal strips or springs in the batteryholder. Six-volt lantern batteries typically feature two coiled, cone-shaped spring terminals...
Standard-format batteries are inserted into batteryholder in the device that uses them. When a device does not uses standard-format batteries, they are typically...
A button cell, watch battery, or coin battery is a small single-cell battery shaped as a squat cylinder typically 5 to 25 mm (0.197 to 0.984 in) in diameter...
List of battery types List of battery sizes Comparison of battery types BatteryholderBattery recycling High capacity oceanographic lithium battery pack...
cells in a D-sized holder. List of battery sizes Battery nomenclature "U.S. Army Flashlight". Life Cycle Impacts of Alkaline Batteries with a Focus on End-of-Life...
previously included MS-D70 batteryholder, which allowed users to mount three CR2 batteries in the camera in case of a dead battery (notably the adapter is...
film holder and rechargeable battery Camera body with 135mm/1:5.6 lens and film holder, without (rechargeable) batteries Body only, without batteries B×L×H...
needed two batteries due to the 8021's higher power consumption, but later units (designed for the TMS1100) only had one active batteryholder. Even though...
cushion. The only official third-party accessory available at launch is a batteryholder made by Belkin. A first-party adapter costing $299 is available and...
vertical grip MB-D200 holds one or two EN-EL3E lithium-ion or six AA batteries in holder tray, provides vertical shutter release, command dials, and AF-ON...
launched its first products in 2024, the Auto-Tracking Stand Pro, and the BatteryHolder for Apple Vision Pro. Stylized in lowercase in its logo. Woodhouse,...
capsules, switch capsules, pontoon capsules, and others; there are also batteryholders, wheels, propellers, impellers, lights, wires, and miscellaneous supporting...
experienced battery corrosion and leakage, resulting in a damaged case and logic board. Some SE models feature a board-mounted batteryholder, while others...
checked for broken/repaired batteryholder compartments. Another common problem is failure of the second internal battery that retains frame number/ISO...
the first patent holder of a battery in Japan was not Yai, but Takahashi Ichisaburo. Wilhelm Hellesen also invented a dry-battery in 1887 and obtained...
internet mystery. Memory Protection Devices, a company that manufactures batteryholders Moonee Ponds railway station, Melbourne UTA MPD, a type of diesel multiple...
sockets Audio and video interfaces and connectors Banana connector BatteryholderBattery terminal Coaxial power connector Computer port (hardware) Crocodile...
Global Information
